BLOG

How do I reset my Canon Pixma printer to factory settings?

techcust1 21.05.2022
0 người theo dõi 0 bình luận 18 bài chia sẻ

Once the printer is on, or the printer is set to print it will wash the print head, and ensure that the printer is prepared for use. Once the print head is cleaned, it produces waste ink, which is disposed of within the kit for ink absorption. The ink absorber kit acts as a pad to store waste ink located at the bottom of the printer.

Ink absorber kit Canon Pixma iP110

If the waste ink container is full and the printer is not working, the error code will display while the printer is being used and reads "Ink absorber full" with error code [5B00]. If this error is encountered it will blink between orange and yellow, and then seven times. If this happens it means that the printer is inoperable and should be repaired as soon as possible.

To fix the full ink waste error, it's accomplished in two phases. The first involves replacing the absorber unit, after the kit has been replaced, the next stage is resetting the counter for waste ink to zero. Once the two phases of repair are completed the printer will be back to normal and may be used once more. Here's the process of fixing to fix the canon ip110 reset with an error ink absorber that is full [5B00Ink absorber full [5B00].

Problem Description

Operator Call Error

Blinking of the Alarm LED 8 times

Error Warning The ink absorber is nearly full. [1700]

Note: When the wasted ink counter is at 95 percent and the printer is notified, it will display an alert "Warning: The ink absorber becomes almost full. [1700]". This message is known as "Operator Call Error". When you notice this warning then use the stop button one time in order to continue printing.

Service Call Errors

Blinking Cycles of Power and Alarm LEDs 7 times

Error: Ink absorber full

Error code overseas: [5B00] [5B01Japan Japan

Notice: When the ink absorber's capacity for waste gets to 100 percent it will display the error code "Ink absorber full [5B00]". It is referred to as"Service Call Error" or "Service Call Error". If this error is triggered the Power and Alarm lights will blink alternately seven times The printer is unable to be utilized.

Solution:

1. Clean or replace the kit for ink absorption.

2. Reset the counter of the ink absorber to zero.

Solution

1. Replace or cleaning the ink absorber kit

The ink absorption kit for Canon Pixma IP110 is located in the lower part of the machine. Be sure to have a brand new ink absorber kit before disassembling your printer. If a new absorber kit isn't on the market an alternative is cleaning the absorber. Learn how to wash an ink absorber kit.

- Take off the absorber kit and place it in a pot that is filled with water.

If the water is cloudy, you should replace it with a fresh one.

Repeat the soak until the absorber kit is completely clean.

- After you've soaked the absorber kit with ink dry it in the sun or air dry it.

- Ensure that the ink absorber kit has been completely dry prior to replacing it.

To clean or replace the ink absorber, you must disassemble the printer as this kit is located at the lower part of the printing device. Follow the steps in the photo below to remove the Canon Pixma iP110 printer.

After the ink absorber unit is repaired then the second step would be put together the printer once more. Be sure that the printer is assembled safely and in a controlled manner, to avoid any possibility of causing further injuries. Once that the kit for ink absorption is replaced or cleaned then the following step involves resetting the counter of the ink absorber to zero.

2. Reset the counter of the ink absorber to zero.

How to fix Canon Pixma iP110 error ink absorber is full 5B00, 5B01

STEP 1 - Enter Service Mode

For a reset on a Canon printer, it is required to be set in the Service mode. Here's how to put the Canon iP110 to enter Service Mode.

Canon Pixma IP110 buttons

Service modes and operating procedures

1.) Switch off the printer.

2.) 2. Press and hold down the STOP button.

3.) Hold and press on the ON button (do not let both buttons go)

4.) Press the STOP button (do not let the ON button go)

5) As you hold your ON button in place, hold the ON button five times, and then remove your ON button.

Note:

1. If D's value is D=100.00 then the main ink absorber kit has to be cleaned or replaced following which the counter for the Main ink absorber has to be reset.

2. In the event that the DpAW value is Dp AW=100.0 The Platen ink absorber needs to be cleaned. After that, you will need to clean the Platen the counter of ink absorbers has to be reset.

3. When the Dp HM value is Dp HM=100.0 The Platen ink absorber has to be cleaned. After that, you will need to clean the Platen ink absorber counter needs to be reset.

4. If DL=000, then the main ink absorber needs to be replaced as the life expectancy has expired.

5. Remove Ink Counter click the ALL (2) and click to SET (3) for the reset of both Main and Platen counters for the ink absorber to zero. Once the counter for ink absorber was reset the counter's value will be printed immediately. You must wait for the printer to end printing.

Done.

Repairing the printer for a full error message for the ink absorber using error message [5B00or [5B01] can be completed in two steps. First, clean or replace an ink absorber. Next, set the counter for waste ink to zero. If you're having difficulty making this yourself We suggest contacting the closest Canon Service Center for help or the closest repair expert for your printer.

0 Bình luận
  • Chưa có bình luận nào cho chủ đề này.
Website liên kết